# LinHT **Source:** [wiki.m17foundation.org](https://wiki.m17foundation.org/index.php?title=LinHT) --- [![](https://wiki.m17foundation.org/images/thumb/0/0c/Linht_outdoor.png/300px-Linht_outdoor.png)](https://wiki.m17foundation.org/index.php?title=File:Linht_outdoor.png) LinHT, as seen in the wild Open-source hardware, Linux-based, SDR handheld transceiver. OpenHT successor with greatly simplified hardware - no FPGAs involved. This project offers a replacement board for the Retevis C62 radio, greatly expanding its capabilities. LinHT is an experimental, community-driven project, not a consumer product. It is aimed at developers, radio amateurs comfortable with Linux, and SDR experimenters. ## Contents # Hardware The device uses a CompuLab MCM-iMX93 System on Module (SoM) running Linux. The RF front-end is based on the Semtech SX1255. The chip is used as a complete IQ modulator/demodulator, allowing for true all-mode support. **UHF only.** The current hardware revisions do not support VHF. The SX1255 PLLs lock between 356 and 562 MHz (measured at room temperature), the usable range also depends on the PA and filter configuration. ### Main components | Device | Role | Main features | | --- | --- | --- | | MCM-iMX93 | Linux System on Module | Dual Cortex-A55, Cortex-M33, 2 GB LPDDR4, 32 GB eMMC | | SX1255 | Direct-IQ RF front-end | Complete IQ transceiver, up to 500 kHz bandwidth | | GRF5604 | RF power amplifier | 100-600 MHz, about 4.5 W CW measured on Rev B | | 2x PE4312 | RX attenuators | 6-bit, 0.5 dB steps, 31.5 dB range each | | SKY13330 | TX/RX switch | SPDT, 0.1-6.0 GHz | | TLV320AIC3100 | Audio codec | Codec with mono class-D speaker amplifier | | LG77L | GNSS receiver | GPS, GLONASS, Galileo, BDS, QZSS | | BQ25792 | Charger and power path | USB-C charging of the 2S battery | | ATtiny826 | Power management controller | Rail sequencing, buttons, boot mode selection, shutdown | ### CPU - Dual-core ARM Cortex-A55 @ 1.7GHz - ARM Cortex-M33 coprocessor @ 250MHz - Floating Point Unit - ARM Ethos U-65 microNPU (Neural Processing Unit with TensorFlow Lite support) ### Memory - 2GB LPDDR4 - 32GB eMMC ### Hardware revisions | Revision | Status | Purpose | | --- | --- | --- | | Rev A | Completed | Architecture proof of concept | | Rev B | Completed | Integrated feature prototype and system testing | | Rev C | Being tested | Targeted corrections based on Rev B testing | See the [Rev B status report](https://m17project.org/2026/06/16/linht-rev-b-status-what-works-what-broke-and-why-rev-c-is-next/) for details. ## Software LinHT runs a custom Yocto-based Linux distribution. Developers can use C/C++/Python as well as (or in conjunction with) GNU Radio flowgraphs and SoapySDR. Tools such as gcc and gdb are built-in. ### Supported modes (so far) Demonstrated on Rev A and Rev B hardware: - FM transmission and reception with pre-/de-emphasis and CTCSS - SSB transmission and reception - M17 - transmission and reception - TETRA - reception only - Demo 64QAM transmission at 2Mbps Other modes can be added later (FreeDV, APRS, etc.). ### Images Prebuilt images for LinHT can be downloaded [here](https://m17project.org/linht/experimental/). Use the folder matching your board revision (_rev\_a_, _rev\_b_ or _rev\_c_). ### Building images Instructions for setting up the Yocto build environment can be found on [here](https://wiki.m17foundation.org/index.php?title=LinHT_Image_Build "LinHT Image Build"). ### Flashing #### Standard: using the Universal Update Utility (_uuu_) To flash the images to LinHT, the [Universal Update Utility](https://github.com/nxp-imx/mfgtools/releases) is needed. LinHT needs to be booted into USB boot (flash) mode first: - **Rev C:** hold the secondary side button while switching the radio on. - **Rev B:** the side button method does not work reliably. Use the alternative method below. Once in flash mode, plug in the USB-C cable, then the image can be written with _uuu_: uuu \-v \-b emmc\_all imx-boot-mcm-imx93-sd.bin-flash\_singleboot linht-image-mcm-imx93.rootfs.wic.zst #### Alternative: mounting the eMMC drive Sometimes, the _uuu_ tool fails to flash the image. It will then exit at 15% (or at some other point) with _libusb_ returning error -1 or -9. Luckily, there is another way to flash the device. Its eMMC drive can be mounted using debug UART exposed at the Kenwood connector. The connection parameters are as follows: 115200 baud, 8 bits, no parity, 1 stop bit, CR-LF line ending. Connect a USB-UART converter (3.3V logic!) at the Kenwood connector and plug in the USB-C cable. Hold any key in the serial terminal while switching the radio on, to stop U-Boot from booting Linux. Then issue a U-Boot command to mount the eMMC drive: ums 0 mmc 0 A new drive should appear (looking like an external flash drive). Then, a tool like _dd_ or Rufus (under Windows) can be used to flash the image: zstdcat /path/to/image.wic.zst | sudo dd of\=/dev/sdX bs\=1M status\=progress where _/dev/sdX_ is the eMMC's mounting point. #### Updating the image To update the image, use SSH to execute fw\_setenv bootcmd "setenv bootcmd '\`fw\_printenv -n bootcmd\`'; saveenv; ums 0 mmc 0" then reboot now This command tells U-Boot to mount the eMMC drive at next boot. The device will reboot. It is now possible to use _dd_ or Rufus with the freshly mounted eMMC to flash the Linux image (see above). After flashing, unmount the drive and reset the device to complete the process. The _bootcmd_ variable will automatically be overwritten with its original contents, such that after reset the device will boot Linux normally. **Note:** this method does _not_ update the boot partition (which includes the device tree). ### Driver To access LinHT's network device under Windows, the RNDIS driver needs to be installed. It is available from the [Microsoft Update Catalog](https://www.catalog.update.microsoft.com/Search.aspx?q=USB%20RNDIS%20Gadget) (search for _USB RNDIS Gadget_). It should work on most Linux distributions out of the box! # Links ### How-tos [LinHT image build](https://wiki.m17foundation.org/index.php?title=LinHT_Image_Build "LinHT Image Build") [LinHT Image Manual](https://wiki.m17foundation.org/index.php?title=LinHT_Image_Manual "LinHT Image Manual") [LinHT Tools](https://wiki.m17foundation.org/index.php?title=LinHT_Tools "LinHT Tools") ### Reference [LinHT Hardware](https://wiki.m17foundation.org/index.php?title=LinHT_Hardware "LinHT Hardware") [LinHT Signal Path](https://wiki.m17foundation.org/index.php?title=LinHT_Signal_Path "LinHT Signal Path") ### Blogs [M17Project.org](https://m17project.org/?s=linht) [uart.cz](https://uart.cz/en/2811/linht-open-sdr-handheld-for-radio-amateurs/) [Zero Retries](https://www.zeroretries.org/i/172905621/linht) ### Presentations [LinHT – a GNU Radio configurable handheld transceiver](https://github.com/M17-Project/M17_education/blob/main/English/M17_Con_2025/M17_Con_2025_LinHT.odp) (en), Wojciech Kaczmarski (SP5WWP), M17 Conference 2025 ([video](https://www.youtube.com/watch?v=ecn54XRD5Oo)) [LinHT: open-source SDR transceiver](https://www.youtube.com/watch?v=PyispKXU68Y) (cz), Vlastimil Slinták (OK5VAS), OpenAlt 2025 # Repositories ### Hardware [LinHT-hw: main LinHT hardware repository](https://github.com/M17-Project/LinHT-hw) (schematics, PCB, Gerbers, BOM) [LinHT-rf-amp: GRF5604 test board](https://github.com/M17-Project/LinHT-rf-amp) ### Software [LinHT-utils: collection of LinHT tools, scripts, tests and the power management firmware](https://github.com/M17-Project/LinHT-utils) [libsx1255: SX1255 control library](https://github.com/M17-Project/libsx1255) [liblinht-ctrl: GPIO, PWM, backlight and attenuator control library](https://github.com/M17-Project/liblinht-ctrl) [LinHT-share: settings file, GNU Radio flowgraphs, fonts, icons and sounds installed to /usr/share/linht](https://github.com/M17-Project/LinHT-share) ### Yocto layers [meta-linht-software: installed software, configuration, ...](https://github.com/M17-Project/meta-linht-software) [meta-linht-hardware: device tree, drivers, U-Boot, ...](https://github.com/M17-Project/meta-linht-hardware) [meta-linht-sdr: GNU Radio packages](https://github.com/M17-Project/meta-linht-sdr) # License The LinHT hardware is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License (CC BY-NC-SA 4.0). Software components carry their own licenses (the Yocto layers, libsx1255 and liblinht-ctrl are GPL-3.0). See each repository for details.